Image 1

ElectroHub (plates only)

0.30 LBS
Calculated at checkout


Related Products
Product Videos
Also Viewed
By Category
Other Details
  • Product Description



    The Rotor Bones ElectroHub Plates 

    1 x Top ElectroHub Plate

    1x Bottom ElectroHub Power Distribution Plate

    NOTE: Electronics sold separately.


    Electrohub Weight : 66 grams



    Recommended Parts:



    Control Board:
    Rev6 Flight control board

    Speed Controllers:
    BLHeli Series 20amp Esc


    1300 - 2200 mah 3S




  • Product Reviews


    Write A Review

    1. Life just got easy

      This product is great! I got a few and no matter what I am building it just make life for me easier. Just put one on a aluminium V tail. Used the top plate to mount the auto pilot and GPS. on 11th Nov 2016

    2. Great Product!

      Re-building a hexacopter that was purchased as a kit a few years ago (before power-distro boards). The Electrohub made the power distribution a snap!

      on 24th Apr 2016

    3. electro hub

      Very nice. Alllows all kinds of configurations and the embedded distribuion panel is a definate plus. on 3rd Apr 2016

    4. Nicely made

      I bought a second set of these to add to my electrohub for additional levels for more on board equipment. Using more stand offs to make a 3 level electrohub. on 19th Mar 2016

    5. Awesome product!

      Ordered the plates and decided to build a Spider Quad. Watched the tutorial on how to assemble it and got started. The Electrohub plates are fantastic! Used 30amp ESC's, 1000kv motors and the CC3D Flight controller. The quad is super stable and fun to fly! Next project will be an Electrohub hexacopter. on 8th Jan 2016

    6. ElectroHub

      I seen these guys build Quads and Hex's with this setup and thought I would give it a try.
      The plates seem very well made and all of the contacts are very well designed. Good job guys
      on 17th Nov 2015

    7. Another great inspiration!

      Thanks Flite Test! I really have cleaned up my wiring now, and if you use some spacers around the normally 1/2" booms, you have plenty of room to mount a receiver or flight controller.

      Just don't be silly and mount your ESCs to the smaller (lower current rated) pads, and you'll be good to go.

      Your booms will break long before this G10 PCB will, but that's the appeal for this for beginners as well...
      on 8th Oct 2015

    8. It was my mistake

      I went back and really looked at what i did Vs. the FliteTest build. I soldered to the small pads for the ESCs. I should have soldered to the large pads the smae ones I soldered the batter cable to. so five stars! on 13th Aug 2015

    9. Love it, but....

      I love it! The PSB pads take solder like a champ. the layout is wonderful there's always somewhere to attach your ESCs. For my first time build It has made it much easier to figure everything out. There is plenty of space to route all of your wires from the ESCs, your FC's breakout cable, and the receiver. The only reason I didn't give it five stars. After my first crash, which only split the ends of two booms where the screws were, ripped off three of the small pads from the PSB. I don't know if my solder joints were that good, it was a defect, or I damaged the pads weakening them when i solder the wires on. I'm still going to buy more of them so not a detractor. just an honest review. on 12th Aug 2015

    10. Great item

      Flite Test Rotor Bones seems to be my first choice, this ElectroHub is a great quality item so versatil I built a pentacopter with it and its working great although in my case it would have been better if it was about 1" larger sense the wiring was a tight squeeze. Still I recomend it on 6th Jul 2015

  • Warranty Information


  • Find Similar Products by Category